Colibry configuration sets
Colibry is the name of the flight configuration folder etc/colibry/ in the Bebop 2 firmware 4.7.1 image. The files are plain-text configuration read by the main flight program. The narrative is at the firmware story. Related references: firmware images, boxinit services, evidence ledger.
All paths are relative to the image root (rootfs). All values are from the 4.7.1 image.
| Status | Meaning |
|---|---|
| Verified | The file or bytes were read directly when this page was written. |
| Agent-cited | Taken from an earlier analysis note and not re-checked against the files. |
| Confirmed independently | A source outside the image files states it (here, the live unit’s own log, as reported by another session). Not read from the image. |
| Open | Not established, or the value is not defined in the file named. |
Directory layout
Section titled “Directory layout”Six sets exist under etc/colibry/. common holds a complete set of nine files. Each board set holds a subset of those files plus three mode folders.
| Set | Top-level files | Mode folders (each holds init.cfg) |
Status | Source |
|---|---|---|---|---|
common |
controller.cfg, drone.cfg, estimator.cfg, event.cfg, helper.cfg, reference.cfg, root.cfg, states.cfg, video.cfg | none | Verified | etc/colibry/common/ |
chimeraboard |
controller.cfg, drone.cfg, estimator.cfg, event.cfg, helper.cfg, reference.cfg, root.cfg, states.cfg, video.cfg | default, fvt, simulator | Verified | etc/colibry/chimeraboard/ |
milosboard |
controller.cfg, drone.cfg, estimator.cfg, event.cfg, helper.cfg, reference.cfg, root.cfg, states.cfg, video.cfg | default, fvt, simulator | Verified | etc/colibry/milosboard/ |
milosblack |
drone.cfg, estimator.cfg, helper.cfg, root.cfg | default, fvt, simulator | Verified | etc/colibry/milosblack/ |
milosthermal |
drone.cfg, estimator.cfg, helper.cfg, reference.cfg, root.cfg | default, fvt, simulator | Verified | etc/colibry/milosthermal/ |
mykonos3board |
controller.cfg, drone.cfg, estimator.cfg, event.cfg, helper.cfg, reference.cfg, root.cfg, states.cfg, video.cfg | default, fvt, simulator | Verified | etc/colibry/mykonos3board/ |
The file barometer_compensation.csv is named in etc/init.d/rcS as a per-set source file. No file with that name exists in any set in this image.
| Item | Observation | Status | Source |
|---|---|---|---|
barometer_compensation.csv |
Absent from every set directory | Verified | etc/colibry/ (search by name over the whole rootfs returned nothing) |
milosblack/root.cfg |
Includes ../../milosboard/reference.cfg, controller.cfg, states.cfg, event.cfg, video.cfg |
Verified | etc/colibry/milosblack/root.cfg, lines 19 to 23 |
milosthermal/root.cfg |
Includes its own reference.cfg; includes ../../milosboard/controller.cfg, states.cfg, event.cfg, video.cfg |
Verified | etc/colibry/milosthermal/root.cfg, lines 19 to 23 |
milosblack and milosthermal init.cfg |
One line each, @include of the matching milosboard mode file |
Verified | etc/colibry/milosblack/*/init.cfg, etc/colibry/milosthermal/*/init.cfg |
Mode folders
Section titled “Mode folders”Each init.cfg selects the value of three keys. The key workingModeInitValue is the selector used by the logSet and adcFsSet tables.
| Set | Folder | takeOffHeightInitValue | demoMagicCarpetInitValue | workingModeInitValue | Status |
|---|---|---|---|---|---|
| chimeraboard, milosboard, mykonos3board | default | “default” | “default” | “default” | Verified |
| chimeraboard, milosboard, mykonos3board | fvt | “fvt” | “fvt” | “fvt” | Verified |
| chimeraboard, milosboard, mykonos3board | simulator | “default” | “default” | “simulator” | Verified |
| milosblack, milosthermal | default, fvt, simulator | via @include of the milosboard file of the same name |
via include | via include | Verified |
The live unit’s log names the mode folder it read, default (see Set selection). Which mode folder other runs use is not established.
Set selection
Section titled “Set selection”The set name is the string returned by the runtime property ro.hardware. The matching lines in the image:
| File | Line | Text | Status |
|---|---|---|---|
etc/init.d/rcS |
261 | COLIBRY_BARO_CSV_FILE_SRC="/etc/colibry/$(gprop ro.hardware)/${COLIBRY_BARO_FILENAME}" |
Verified |
usr/bin/DragonStarter.sh |
186 | if [ "$(gprop ro.hardware)" = "chimeraboard" ] |
Verified |
bin/ardrone3_shell.sh |
8 | if [ "$(gprop ro.hardware)" = "milosboard" ] |
Verified |
bin/ardrone3_shell.sh |
13 | elif [ "$(gprop ro.hardware)" = "chimeraboard" ] |
Verified |
bin/onoffbutton/shortpress_3.sh |
22 | (if [ "$(gprop ro.hardware)" = "milosboard" ]; then |
Verified |
bin/onoffbutton/shortpress_3.sh |
39 | elif [ "$(gprop ro.hardware)" = "mykonos3board" ]; then |
Verified |
Two boxinit files also import by the property: etc/boxinit.hosted.rc line 6 reads import boxinit.hosted.${ro.hardware}.rc and etc/boxinit.standalone.rc line 6 reads import boxinit.standalone.${ro.hardware}.rc (Verified). The image contains etc/boxinit.standalone.milosboard.rc and etc/boxinit.standalone.mykonos3board.rc and no chimeraboard equivalent (Verified). See boxinit services.
In bin/ardrone3_shell.sh, the milosboard branch sets PRODUCT="Bebop2" and PRODUCT_MODEL_ID="090c"; the chimeraboard branch sets PRODUCT="Bluegrass" and PRODUCT_MODEL_ID="0916" (Verified, lines 10 and 11, 15 and 16).
Build variant, from etc/build.prop:
| Key | Value | Status |
|---|---|---|
| ro.build.alchemy.variant | milos | Verified |
| ro.parrot.build.variant | milos | Verified |
| ro.parrot.build.uid | ardrone3-milos-4.7.1 | Verified |
| ro.parrot.build.version | 4.7.1 | Verified |
No file in the image assigns a value to ro.hardware; the property is only read (Verified by search over the rootfs for the string).
Open points:
| Question | Status |
|---|---|
Which set the Bebop 2 loads. A system log file on one unit’s own storage states the board in its own words (“My hardware is milosboard”) and that the configuration was read from etc/colibry/milosboard/root.cfg with the include path etc/colibry/milosboard/default. That also settles the mode folder for that unit (default). It was reported by another session and is not in the image files. |
Confirmed independently |
| Which set other Bebop 2 units load. Only one unit was checked. | Open |
How common is layered under a board set. Board root.cfg files include their own sibling files by relative path (../drone.cfg, ../controller.cfg and so on). No root.cfg of a board set names common. Board files define only a subset of keys that common defines, which is consistent with a fall-back to common, but the loader that resolves includes is compiled code and was not checked. The layering reading is the earlier analysis’s. |
Agent-cited |
Whether a key absent from a board set takes its value from common. Consistent with it: see the observation below the table. |
Open |
Observation (Verified): the root.cfg of each board set includes paths such as ../drone.cfg and ../../milosboard/controller.cfg. No file etc/colibry/drone.cfg exists, and each mode folder (default, fvt, simulator) holds only init.cfg. Those paths land on the intended files only if the include is resolved from inside a mode folder of the set. That the loader does this is an inference and is Open; the loader was not inspected.
Observation (supporting, not proof): the mass values in drone.cfg are 0.500 kg (milosboard), 0.523 kg (milosblack), 0.604 kg (milosthermal) and 0.390 kg (mykonos3board). Parrot’s published datasheets list a weight of 604 g for the Bebop-Pro Thermal drone and 500 g for the Bebop 2 Power, and the 3D modeling datasheet calls the Bebop 2 a “500g category” drone. The 604 g figure matches milosthermal exactly and the 500 g figure matches milosboard. That pointed a Bebop 2 toward milosboard before the unit’s own log was read; the log then gave the same answer.
Observation (supporting the layering question, not proof): milosboard defines none of the keys maxVerticalSpeed, usrConfigVerticalSpeed, usrConfigMaxAngularRateRefFlying, usrConfigMaxDistance or usrConfigNoFlyOverMaxDistance, and angleRefMaxUser only in chimeraboard and mykonos3board. The limits one Bebop 2 unit reports over its normal protocol equal the common values for these: a maximum tilt of 35 degrees, a maximum vertical speed of 6 m/s and default of 1 m/s, a maximum pitch/roll rotation speed of 300 deg/s, a maximum distance of 2000 m and the geofence off. That is consistent with a board set falling back to common. The match between a protocol field and a config key is an inference from names and units. Two other reported ranges do not match any key here (a maximum altitude of 150 m against usrConfigMaxAltitude 1000.0, and a yaw rotation speed range of 10 to 200 deg/s against usrConfigRotationSpeed 180.0), so not every reported range comes from these files.
The earlier analysis note states the Bebop 2 set is milosboard layered on common; the first half is not established by the files, and the second half is the Agent-cited reading above.
Selected parameters, side by side
Section titled “Selected parameters, side by side”Cell text “inherits or absent” means the file for that set does not define the key. The inherited value is not stated here. Values listed in a row were each read from the file named. A row is marked Open when it has at least one such cell.
milosblack and milosthermal have no controller.cfg, reference.cfg (milosblack), states.cfg, event.cfg or video.cfg of their own; their root.cfg includes the milosboard copy. A cell for those sets reads “via milosboard file” where that include applies.
Estimator rate
Section titled “Estimator rate”| Set | adcFsSet default | adcFsSet fvt | adcFsSet simulator | Status | Source |
|---|---|---|---|---|---|
| common | inherits or absent | inherits or absent | inherits or absent | Open | etc/colibry/common/root.cfg (defines only adcTs = 1.0) |
| chimeraboard | 198.3642578125 | 198.3642578125 | 200.0 | Verified | etc/colibry/chimeraboard/root.cfg, lines 8 to 13 |
| milosboard | 198.3642578125 | 198.3642578125 | 200.0 | Verified | etc/colibry/milosboard/root.cfg, lines 8 to 13 |
| milosblack | 198.3642578125 | 198.3642578125 | 200.0 | Verified | etc/colibry/milosblack/root.cfg, lines 8 to 13 |
| milosthermal | 198.3642578125 | 198.3642578125 | 200.0 | Verified | etc/colibry/milosthermal/root.cfg, lines 8 to 13 |
| mykonos3board | 198.3642578125 | 198.3642578125 | 200.0 | Verified | etc/colibry/mykonos3board/root.cfg, lines 8 to 13 |
The comment in root.cfg states: Runtime operation : adcTs = adcTs/adcFs. No unit is written beside adcFsSet.
Sensor rates and GPS period
Section titled “Sensor rates and GPS period”| Set | barometerFrequency [Hz] | ultrasoundFrequency [Hz] | dtGps [s] | Status | Source |
|---|---|---|---|---|---|
| common | 75.0 | 15.0 | 0.200000002980232 | Verified | common/helper.cfg lines 84 and 65; common/estimator.cfg line 105 |
| chimeraboard | inherits or absent | inherits or absent | inherits or absent | Open | none of the three keys in the set’s files |
| milosboard | inherits or absent | inherits or absent | inherits or absent | Open | none of the three keys in the set’s files |
| milosblack | inherits or absent | inherits or absent | inherits or absent | Open | none of the three keys in the set’s files |
| milosthermal | inherits or absent | inherits or absent | inherits or absent | Open | none of the three keys in the set’s files |
| mykonos3board | inherits or absent | inherits or absent | inherits or absent | Open | none of the three keys in the set’s files |
The comment beside dtGps reads [s] 5Hz measures + quartz clock diff with IMU.
Mass and inertia
Section titled “Mass and inertia”Units from the comments: mass [kg], J [kg.m2].
| Set | mass | Jx | Jy | Jz | Status | Source |
|---|---|---|---|---|---|---|
| common | inherits or absent | inherits or absent | inherits or absent | inherits or absent | Open | common/drone.cfg (11 lines, no mass or inertia keys) |
| chimeraboard | 1.893 | 0.0172 | 0.0200 | 0.0295 | Verified | chimeraboard/drone.cfg lines 18 to 21 |
| milosboard | 0.500 | 0.001491 | 0.001458 | 0.003328 | Verified | milosboard/drone.cfg lines 18 to 21 |
| milosblack | 0.523 | 0.001491 | 0.001458 | 0.003328 | Verified | milosblack/drone.cfg lines 18 to 21 |
| milosthermal | 0.604 | 0.001491 | 0.001968 | 0.00416 | Verified | milosthermal/drone.cfg lines 18 to 21 |
| mykonos3board | 0.390 | 0.000969 | 0.00133 | 0.00343 | Verified | mykonos3board/drone.cfg lines 18 to 21 |
Motor speed limits and coefficients
Section titled “Motor speed limits and coefficients”Units from the comments: speeds [RPM], motorA [N.RPM-2], motorB [N.m.RPM-2]. The comment beside motorA and motorB is written in French and reads Coeff quadratiques. Each array has four entries, one per motor.
| Set | motorsRpmMax | motorsRpmMin | motorA (all four) | motorB | Status | Source |
|---|---|---|---|---|---|---|
| common | inherits or absent | inherits or absent | inherits or absent | inherits or absent | Open | common/drone.cfg |
| chimeraboard | 7100.0 | 1000.0 | 2.0983e-07 | -4.0e-09, 4.0e-09, -4.0e-09, 4.0e-09 | Verified | chimeraboard/drone.cfg lines 23 to 27 |
| milosboard | 12200.0 | 3000.0 | 2.15e-8 | -2.85e-10, 2.85e-10, -2.85e-10, 2.85e-10 | Verified | milosboard/drone.cfg lines 23 to 27 |
| milosblack | 12200.0 | 3000.0 | 2.15e-8 | -2.85e-10, 2.85e-10, -2.85e-10, 2.85e-10 | Verified | milosblack/drone.cfg lines 23 to 27 |
| milosthermal | 12200.0 | 3000.0 | 2.15e-8 | -2.85e-10, 2.85e-10, -2.85e-10, 2.85e-10 | Verified | milosthermal/drone.cfg lines 23 to 27 |
| mykonos3board | 11000.0 | 3000.0 | 1.74e-8 | 2.39e-10, -2.39e-10, 2.39e-10, -2.39e-10 | Verified | mykonos3board/drone.cfg lines 23 to 27 |
Motor positions
Section titled “Motor positions”Unit from the comments: [m]. Entries are in motor order.
| Set | motorX | motorY | Status | Source |
|---|---|---|---|---|
| common | inherits or absent | inherits or absent | Open | common/drone.cfg |
| chimeraboard | 0.149, 0.149, -0.149, -0.149 | -0.186, 0.186, 0.186, -0.186 | Verified | chimeraboard/drone.cfg lines 31 and 32 |
| milosboard | 0.0875, 0.0875, -0.0875, -0.0875 | -0.115, 0.115, 0.115, -0.115 | Verified | milosboard/drone.cfg lines 31 and 32 |
| milosblack | 0.0875, 0.0875, -0.0875, -0.0875 | -0.115, 0.115, 0.115, -0.115 | Verified | milosblack/drone.cfg lines 31 and 32 |
| milosthermal | 0.0975, 0.0975, -0.0775, -0.0775 | -0.119, 0.111, 0.111, -0.119 | Verified | milosthermal/drone.cfg lines 31 and 32 |
| mykonos3board | 0.0775, 0.0775, -0.0775, -0.0775 | -0.0975, 0.0975, 0.0975, -0.0975 | Verified | mykonos3board/drone.cfg lines 31 and 32 |
Video tilt range
Section titled “Video tilt range”Unit from the comment: In deg. The files milosboard/video.cfg and chimeraboard/video.cfg contain only a header comment.
| Set | videoTiltRange | Status | Source |
|---|---|---|---|
| common | [-75.0, 30.0] | Verified | common/video.cfg line 8 |
| chimeraboard | inherits or absent | Open | chimeraboard/video.cfg |
| milosboard | inherits or absent | Open | milosboard/video.cfg |
| milosblack | via milosboard file: inherits or absent | Open | milosblack/root.cfg line 23 |
| milosthermal | via milosboard file: inherits or absent | Open | milosthermal/root.cfg line 23 |
| mykonos3board | [-70.0, 35.0] | Verified | mykonos3board/video.cfg line 5 |
Attitude gains, set “Default”
Section titled “Attitude gains, set “Default””The key gainsQuaternionSet is selected by gainsQuaternionSetInitValue and holds three entries: Default, Flip, Rescue. Units from the comments: KP [s-2], KI [s-3], KD [s-1], KDD No units. Within each set listed below, the theta and phi values of the three entries are identical; the entries differ in the psi values. The comments do not name the axes that theta, phi and psi refer to.
| Set | thetaKP | thetaKI | thetaKD | phiKP | phiKI | phiKD | Status | Source |
|---|---|---|---|---|---|---|---|---|
| common | 140.0 | 140.0 | 15.0 | 140.0 | 140.0 | 15.0 | Verified | common/controller.cfg lines 11 to 17 |
| chimeraboard | 64.7 | 0.65 | 14.3 | 64.7 | 0.65 | 14.3 | Verified | chimeraboard/controller.cfg lines 11 to 17 |
| milosboard | 264.7408 | 264.7408 | 33.0926 | 242.5376 | 242.5376 | 30.3349 | Verified | milosboard/controller.cfg lines 11 to 17 |
| milosblack | via milosboard file | via milosboard file | via milosboard file | via milosboard file | via milosboard file | via milosboard file | Verified | milosblack/root.cfg line 20 (values as milosboard) |
| milosthermal | via milosboard file | via milosboard file | via milosboard file | via milosboard file | via milosboard file | via milosboard file | Verified | milosthermal/root.cfg line 20 (values as milosboard) |
| mykonos3board | 171.4027 | 171.4027 | 21.4253 | 169.0922 | 169.0922 | 21.7435 | Verified | mykonos3board/controller.cfg lines 11 to 17 |
Altitude gain sets
Section titled “Altitude gain sets”The key ctrlGainAltitudeSet is selected by ctrlGainAltitudeSetInitValue. Units from the comments: kp [s-2], ki [s-3], kd [s-1].
| Set | Name | kp | ki | kd | Status | Source |
|---|---|---|---|---|---|---|
| common | Default | 4.170 | 1.158 | 5.800 | Verified | common/controller.cfg, ctrlGainAltitudeSet |
| common | Freefall | 2.0 | 0.0 | 15.01 | Verified | same |
| common | Throttle | 0.0 | 0.0 | 0.0 | Verified | same |
| chimeraboard | Default | 6.161 | 2.317 | 7.274 | Verified | chimeraboard/controller.cfg lines 56 to 69 |
| chimeraboard | Freefall | 2.0 | 0.0 | 15.01 | Verified | same |
| chimeraboard | Throttle | inherits or absent | inherits or absent | inherits or absent | Open | not defined in the set’s file |
| milosboard, milosblack, milosthermal | Default, Freefall, Throttle | inherits or absent | inherits or absent | inherits or absent | Open | ctrlGainAltitudeSet not defined in milosboard/controller.cfg |
| mykonos3board | Default, Freefall, Throttle | inherits or absent | inherits or absent | inherits or absent | Open | ctrlGainAltitudeSet not defined in mykonos3board/controller.cfg |
Tilt, speed and altitude limits
Section titled “Tilt, speed and altitude limits”Units are quoted from the comment beside each key. The key maxHorizontalSpeed has no unit in its comment.
| Key | common | chimeraboard | milosboard family | mykonos3board | Unit (comment) | Status | Source |
|---|---|---|---|---|---|---|---|
| angleRefMaxUser | [35.0, 35.0] | [25.0, 25.0] | inherits or absent | [30.0, 30.0] | [deg] |
Open | */reference.cfg line 7 |
| usrConfigMaxTilt | 15.0000009536743 | inherits or absent | inherits or absent | inherits or absent | In degrees |
Open | common/reference.cfg line 25 |
| maxVerticalSpeed | 6.0 | inherits or absent | inherits or absent | inherits or absent | [m.s-1] |
Open | common/reference.cfg line 113 |
| minVerticalSpeedUser | -6.0 | inherits or absent | inherits or absent | inherits or absent | [m/s] |
Open | common/reference.cfg line 106 |
| maxHorizontalSpeed | 12.0 | inherits or absent | inherits or absent | inherits or absent | none | Open | common/reference.cfg line 146 |
| maxHorizontalAcceleration | 3.0 | inherits or absent | inherits or absent | inherits or absent | none | Open | common/reference.cfg line 145 |
| maxVerticalAccelerationForFlying | 6.0 | inherits or absent | inherits or absent | 4.0 | [m.s-2] |
Open | common/reference.cfg line 103; mykonos3board/reference.cfg |
| speedToReturnHome | 8.0 | inherits or absent | inherits or absent | 5.0 | In m/s |
Open | common/reference.cfg line 337; mykonos3board/reference.cfg line 31 |
| usrConfigMaxAltitude | 1000.0 | inherits or absent | inherits or absent | inherits or absent | In m |
Open | common/reference.cfg line 139 |
| maxSpeedIntegral (controller) | [10.0, 10.0] | inherits or absent | [11.6667, 11.6667] | inherits or absent | [deg] |
Open | common/controller.cfg line 153; milosboard/controller.cfg line 56 |
“milosboard family” covers milosboard, milosblack and milosthermal. For angleRefMaxUser, milosboard/reference.cfg holds only a header comment, milosblack includes that file, and milosthermal/reference.cfg defines only swipeRotationSpeed = 60.0 with the unit In deg/s (common value 180.0). The key named minVerticalSpeed in mykonos3board/reference.cfg (value -2.5, unit In m.s-1) has a different name from the common key minVerticalSpeedUser.
Parameter-name prefix glossary
Section titled “Parameter-name prefix glossary”Each entry gives what the nearest comment in the files states. Where no comment states a meaning, the entry says so.
| Prefix or name | Comment text or unit | Example | Status | Source |
|---|---|---|---|---|
| theta, phi, psi (with KP, KI, KD, KDD) | KP [s-2], KI [s-3], KD [s-1], KDD No units; axes not named in comments |
thetaKP | Verified | common/controller.cfg lines 11 to 22 |
| kp, ki, kd (in ctrlGain* groups) | [s-2], [s-3], [s-1] for altitude, position and similar |
ctrlGainAltitudeSet | Verified | common/controller.cfg |
| ctrlGainSpeed kp, ki, kd | [rad.m-1.s], [rad.m-1], [rad.m-1.s-1] |
ctrlGainSpeed | Verified | common/controller.cfg |
| motors* and motor* | [RPM] for speeds; motorA [N.RPM-2]; motorB [N.m.RPM-2]; motorX and motorY [m]; motorAlpha and motorBeta [rad] |
motorsRpmMax | Verified | milosboard/drone.cfg lines 23 to 32 |
| mass, Jx, Jy, Jz | [kg], [kg.m2] |
mass | Verified | milosboard/drone.cfg lines 18 to 21 |
| Cx, Cy, Cz (NoShell, Shell), Cr | [s-1]; meaning not stated in comments |
CxNoShell | Verified | milosboard/drone.cfg lines 5 to 11 |
| pwmMotorsModel keys | [V.s/rpm], [V/rpm], [V/rpm2], [PWM], [rpm/V], [A/rpm²] |
motorsKv | Verified | milosboard/drone.cfg lines 38 to 47 |
| rpm* in controller.cfg | [rad/s2] for rpmMaxAttitudeCommandSet and rpmMaxYawCommand; [m.s-2] for rpmMinForControl |
rpmMinForControl | Verified | common/controller.cfg |
| height* and altitudeCommand* | [m.s-2] for feedforward and command limits; [m/s2] for heightCommandMax |
heightFeedforwardCommandMax | Verified | common/controller.cfg |
| angleRef*, angleSaturation* | [deg], In deg/s |
angleRefMaxUser | Verified | common/reference.cfg lines 7 to 17 |
| usrConfig* | user-setting limits: In degrees, In deg.s-1, In m, In m.s-1, [g] |
usrConfigMaxTilt | Verified | common/reference.cfg lines 25 to 141 |
| maxVertical*, minVertical* | [m.s-2], [m.s-1], [m/s] |
maxVerticalSpeed | Verified | common/reference.cfg lines 103 to 115 |
| animation* | [m/s], [m], [deg] per key |
animationSpeedMin | Verified | common/reference.cfg lines 168 to 277 |
| followMe* | [m/s], [m/s2], [deg/s], [m], [s] per key |
followMeDefaultRelativeSpeed | Verified | common/reference.cfg lines 153 to 159 |
| gainQuatIdealModel* | [s-1] for angle and rate, [] for acceleration, [s] for jerk |
gainQuatIdealModelTiltAngle | Verified | common/reference.cfg lines 30 to 33 |
| verticalModel* | [s-1] for Cz terms; [kg-1] for gamma terms; [m.s-2] for covR |
verticalModelInitCz | Verified | chimeraboard/estimator.cfg |
| battery* | [Wh] for energy; [V] for voltage; [V²] and [] for model noise and beta |
batteryEnergyMax | Verified | milosboard/helper.cfg, common/estimator.cfg |
| shutdownVoltage, nominalVoltage | [V]; the comment on shutdownVoltage reads Will be compared with the estimated no load voltage |
shutdownVoltage | Verified | common/estimator.cfg line 251 |
| landingPower, hoveringPower, RTHPower | [W] |
hoveringPower | Verified | milosboard/helper.cfg |
| ultrasound*, altitudeUS*, Us* | [Hz] for frequency; [m] for noise and bias |
ultrasoundFrequency | Verified | common/helper.cfg lines 48 to 51, common/estimator.cfg line 105 |
| gps* and threshold*Gps | [m], [m/s], [°]; gpsLag has no unit |
gpsAltDeviationErrorMax | Verified | common/helper.cfg lines 57 to 64 |
| altGroundDetectThreshold, flyawayDetectionActive | In m; boolean |
altGroundDetectThreshold | Verified | common/event.cfg, milosboard/event.cfg |
| filterImu* | filter coefficient arrays; no comment | filterImuBCoef | Verified | common/helper.cfg lines 9 and 10 |
| adcTs, adcFsSet | Runtime operation : adcTs = adcTs/adcFs |
adcFsSet | Verified | common/root.cfg line 3 (adcTs and the comment); adcFsSet itself is defined in the board sets’ root.cfg, lines 8 to 13 |
| logSet, enabledSensorsSet | selectors on workingModeInitValue; logging verbosity per node; sensor enables |
logSet | Verified | common/root.cfg |
| fusion*, enabled* | booleans; no comment | fusionVzGps | Verified | milosboard/helper.cfg line 11 |
Comments
Spotted a mistake, or tried this on your own Bebop? Leave a note. Comments are kept on this site's own server.