ARSDK commands: Ardrone3
Part of the ARSDK command reference. Read its section on how to read the tables first. Tags in the cells: V Verified, A Agent-cited, I Inference, O Open.
Project id 1. The Bebop-era command set: piloting, camera, settings, media, GPS. Documented in ardrone3.xml apart from FlatTrim and its event.
Ardrone3.Piloting (class 0)
Section titled “Ardrone3.Piloting (class 0)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| FlatTrim | 1.0.0 | receive | (none) | Level calibration on the ground, going by the name and the posted message FLAT_TRIM (I). | REG 0x60a60 cb 0x58668; msg 6 FLAT_TRIM (A) | not in vendored XML; PROVENANCE.md says upstream lacks it too, although the firmware accepts it (A). |
| TakeOff | 1.0.1 | receive | (none) | Take off. Ask the drone to take off. On the fixed wings (such as Disco): not used except to cancel a land. (V: XML) | REG 0x60a9c cb 0x58564; msg 7 TAKEOFF (A) | |
| PCMD | 1.0.2 | receive | flag:u8; roll:i8; pitch:i8; yaw:i8; gaz:i8; timestampAndSeqNum:u32 | Move the drone. The libARController is sending the command each 50ms. Please note that you should call setPilotingPCMD and not sendPilotingPCMD because the libARController is handling the periodicity and the buffer on which it is sent. (V: XML) | REG 0x60a88 cb 0x58f60; msg 15 PILOTING_COMMAND (A) | |
| Landing | 1.0.3 | receive | (none) | Land. Please note that on copters, if you put some positive gaz (in the PilotingCommand) during the landing, it will cancel it. (V: XML) | REG 0x60abc cb 0x58458; msg 12 LAND (A) | |
| Emergency | 1.0.4 | receive | (none) | Cut out the motors. This cuts immediatly the motors. The drone will fall. This command is sent on a dedicated high priority buffer which will infinitely retry to send it if the command is not delivered. (V: XML) | REG 0x60a74 cb 0x585f0; msg 13 EMERGENCY (A) | |
| NavigateHome | 1.0.5 | receive | start:u8 | Return home. Ask the drone to fly to its HomePosition. The availability of the return home can be get from ReturnHomeState. Please note that the drone will wait to be hovering to start its return home. This means that it will wait to have a flag set at 0. (V: XML) | REG 0x60ad0 cb 0x565dc; msg 14 RETURN_HOME (A) | |
| MoveBy | 1.0.7 | receive | dX:float; dY:float; dZ:float; dPsi:float | Move the drone to a relative position and rotate heading by a given angle. Moves are relative to the current drone orientation, (drone’s reference). Also note that the given rotation will not modify the move (that is, moves are always rectilinear). (V: XML) | REG 0x60ae4 cb 0x583c4; msg 16 MOVE_BY_COMMAND (A) | XML: 090c from firmware 3.3.0 |
| UserTakeOff | 1.0.8 | receive | state:u8 | Prepare the drone to take off. On copters: initiates the thrown takeoff. Note that the drone will do the thrown take off even if it is steady. On fixed wings: initiates the take off process on the fixed wings. (V: XML) | REG 0x610a4 cb 0x584d0; msg 11 THROWN_TAKEOFF_ABORTED, 9 WAIT_THROWN_TAKEOFF (A) | XML: 090c from firmware 4.3.0 |
| MoveTo | 1.0.10 | receive | latitude:double; longitude:double; altitude:double; orientation_mode:enum{NONE="0,TO_TARGET=1,HEADING_START=2,HEADING_DURING=3"}; heading:float | Move to a location. Move the drone to a specified location. If a new command moveTo is sent, the drone will immediatly run it (no cancel will be issued). If a CancelMoveTo command is sent, the moveTo is stopped. (V: XML) | REG 0x60af8 cb 0x564c8; msg 130 MAVLINK_MOVETO_START (A) | XML: 090c from firmware 4.3.0 |
| CancelMoveTo | 1.0.11 | receive | (none) | Cancel the moveTo. Cancel the current moveTo. If there is no current moveTo, this command has no effect. (V: XML) | REG 0x60b0c cb 0x58ee8; no msg id found (O) | XML: 090c from firmware 4.3.0; Callback 0x58ee8 tail-calls 0xb3620 with r1 = 2 and r0 = word 1 of the user data; it does not use the 0x6a374 poster. Effect not traced (V listing, O effect). |
| StartPilotedPOI | 1.0.12 | receive | latitude:double; longitude:double; altitude:double | Start a piloted Point Of Interest. During a piloted POI, the drone will always look at the given POI but can be piloted normally. However, yaw value is ignored. Camera tilt and pan command is also ignored. Ignored if PilotedPOI state is UNAVAILABLE. (V: XML) | REG 0x60b2c cb 0x58200; msg 22 START_POI (A) | XML: deprecated; XML: 090c from firmware 4.3.0 |
| StopPilotedPOI | 1.0.13 | receive | (none) | Stop the piloted Point Of Interest (with or without gimbal control). If PilotedPOI or PilotedPOIV2 state is RUNNING or PENDING, stop it. (V: XML) | REG 0x60b40 cb 0x58188; msg 23 STOP_POI (A) | XML: 090c from firmware 4.3.0 |
Ardrone3.Camera (class 1)
Section titled “Ardrone3.Camera (class 1)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| Orientation | 1.1.0 | receive | tilt:i8; pan:i8 | Move the camera. You can get min and max values for tilt and pan using CameraInfo. (V: XML) | REG 0x60b54 cb 0x580e8; msg 33 CAMERA_ORIENTATION (A) | XML: deprecated |
| OrientationV2 | 1.1.1 | receive | tilt:float; pan:float | Move the camera. You can get min and max values for tilt and pan using CameraInfo. (V: XML) | REG 0x60b68 cb 0x5805c; msg 34 CAMERA_ORIENTATIONV2 (A) | |
| Velocity | 1.1.2 | receive | tilt:float; pan:float | Move the camera using velocity. Move the camera given velocity consign. You can get min and max values for tilt and pan using CameraVelocityRange. (V: XML) | REG 0x60b7c cb 0x57fd0; msg 36 CAMERA_VELOCITY (A) |
Ardrone3.PilotingSettings (class 2)
Section titled “Ardrone3.PilotingSettings (class 2)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| MaxAltitude | 1.2.0 | receive | current:float | Set max altitude. The drone will not fly over this max altitude when it is in manual piloting. Please note that if you set a max altitude which is below the current drone altitude, the drone will not go to given max altitude. (V: XML) | REG 0x60c44 cb 0x563b8; msg 63 SET_MAX_ALTITUDE (A) | |
| MaxTilt | 1.2.1 | receive | current:float | Set max pitch/roll. This represent the max inclination allowed by the drone. You can get the bounds with the commands MaxPitchRoll. (V: XML) | REG 0x60ca0 cb 0x56180; msg 68 SET_MAX_TILT (A) | |
| MaxDistance | 1.2.3 | receive | value:float | Set max distance. You can get the bounds from the event MaxDistance. If Geofence is activated, the drone won’t fly over the given max distance. (V: XML) | REG 0x60c58 cb 0x562dc; msg 65 SET_MAX_DISTANCE (A) | |
| NoFlyOverMaxDistance | 1.2.4 | receive | shouldNotFlyOver:u8 | Enable geofence. If geofence is enabled, the drone won’t fly over the given max distance. You can get the max distance from the event MaxDistance. (V: XML) | REG 0x60c6c cb 0x56208; msg 66 SET_NO_FLY_OVER_MAX_DISTANCE (A) | |
| SetAutonomousFlightMaxHorizontalSpeed | 1.2.5 | receive | value:float | Set autonomous flight max horizontal speed. This will only be used during autonomous flights such as moveBy. (V: XML) | REG 0x60d40 cb 0x55dc8; msg 103 SET_AUTONOMOUS_FLIGHT_MAX_HORIZONTAL_SPEED (A) | XML: 090c from firmware 3.3.0 |
| SetAutonomousFlightMaxVerticalSpeed | 1.2.6 | receive | value:float | Set autonomous flight max vertical speed. This will only be used during autonomous flights such as moveBy. (V: XML) | REG 0x60d54 cb 0x55d40; msg 104 SET_AUTONOMOUS_FLIGHT_MAX_VERTICAL_SPEED (A) | XML: 090c from firmware 3.3.0 |
| SetAutonomousFlightMaxHorizontalAcceleration | 1.2.7 | receive | value:float | Set autonomous flight max horizontal acceleration. This will only be used during autonomous flights such as moveBy. (V: XML) | REG 0x60d68 cb 0x55cb8; msg 105 SET_AUTONOMOUS_FLIGHT_MAX_HORIZONTAL_ACCELERATION (A) | XML: 090c from firmware 3.3.0 |
| SetAutonomousFlightMaxVerticalAcceleration | 1.2.8 | receive | value:float | Set autonomous flight max vertical acceleration. This will only be used during autonomous flights such as moveBy. (V: XML) | REG 0x60d7c cb 0x55c30; msg 106 SET_AUTONOMOUS_FLIGHT_MAX_VERTICAL_ACCELERATION (A) | XML: 090c from firmware 3.3.0 |
| SetAutonomousFlightMaxRotationSpeed | 1.2.9 | receive | value:float | Set autonomous flight max rotation speed. This will only be used during autonomous flights such as moveBy. (V: XML) | REG 0x60d2c cb 0x55e50; msg 102 SET_AUTONOMOUS_FLIGHT_MAX_ROTATION_SPEED (A) | XML: 090c from firmware 3.3.0 |
| BankedTurn | 1.2.10 | receive | value:u8 | Set banked turn mode. When banked turn mode is enabled, the drone will use yaw values from the piloting command to infer with roll and pitch on the drone when its horizontal speed is not null. (V: XML) | REG 0x60cb4 cb 0x560f8; msg 70 SET_BANKED_TURN (A) | XML: 090c from firmware 3.2.0 |
| SetMotionDetectionMode | 1.2.16 | receive | enable:u8 | Enable/disable the motion detection. If the motion detection is enabled, the drone will send its MotionState when its FlyingState is landed. If the motion detection is disabled, MotionState is steady. (V: XML) | REG 0x60c8c cb 0x578a0; msg 67 SET_MOTION_DETECTION (A) | XML: 090c from firmware 4.3.0 |
Ardrone3.MediaRecordEvent (class 3)
Section titled “Ardrone3.MediaRecordEvent (class 3)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| PictureEventChanged | 1.3.0 | send | event:enum{taken="0,failed=1"}; error:enum{ok="0,unknown=1,busy=2,notAvailable=3,memoryFull=4,lowBattery=5"} | Picture taken. This event is a notification, you can’t retrieve it in the cache of the device controller. (V: XML) | GEN 0x59ec4 | |
| VideoEventChanged | 1.3.1 | send | event:enum{start="0,stop=1,failed=2"}; error:enum{ok="0,unknown=1,busy=2,notAvailable=3,memoryFull=4,lowBattery=5,autoStopped=6"} | Video record notification. This event is a notification, you can’t retrieve it in the cache of the device controller. (V: XML) | GEN 0x5a0e4 |
Ardrone3.PilotingState (class 4)
Section titled “Ardrone3.PilotingState (class 4)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| FlatTrimChanged | 1.4.0 | send | (none) | Event reporting that a flat trim was done (I). | GEN 0x594c8 | not in vendored XML |
| FlyingStateChanged | 1.4.1 | send | state:enum{landed="0,takingoff=1,hovering=2,flying=3,landing=4,emergency=5,usertakeoff=6,motor_ramping=7,emergency_landing=8"} | Flying state. (V: XML) | GEN 0x5d120 | |
| AlertStateChanged | 1.4.2 | send | state:enum{none="0,user=1,cut_out=2,critical_battery=3,low_battery=4,too_much_angle=5"} | Alert state. (V: XML) | GEN 0x5d28c | |
| NavigateHomeStateChanged | 1.4.3 | send | state:enum{available="0,inProgress=1,unavailable=2,pending=3"}; reason:enum{userRequest="0,connectionLost=1,lowBattery=2,finished=3,stopped=4,disabled=5,enabled=6"} | Return home state. Availability is related to gps fix, magnetometer calibration. (V: XML) | GEN 0x5925c | |
| PositionChanged | 1.4.4 | send | latitude:double; longitude:double; altitude:double | Drone’s position changed. (V: XML) | GEN 0x595d8 | |
| SpeedChanged | 1.4.5 | send | speedX:float; speedY:float; speedZ:float | Drone’s speed changed. Expressed in the NED referential (North-East-Down). (V: XML) | GEN 0x5980c | |
| AttitudeChanged | 1.4.6 | send | roll:float; pitch:float; yaw:float | Drone’s attitude changed. (V: XML) | GEN 0x5991c | |
| AltitudeChanged | 1.4.8 | send | altitude:double | Drone’s altitude changed. The altitude reported is the altitude above the take off point. To get the altitude above sea level, see PositionChanged. (V: XML) | GEN 0x59a30 | |
| GpsLocationChanged | 1.4.9 | send | latitude:double; longitude:double; altitude:double; latitude_accuracy:i8; longitude_accuracy:i8; altitude_accuracy:i8 | Drone’s location changed. This event is meant to replace PositionChanged. (V: XML) | GEN 0x596fc | XML: 090c from firmware 4.0.0 |
| MoveToChanged | 1.4.12 | send | latitude:double; longitude:double; altitude:double; orientation_mode:enum{NONE="0,TO_TARGET=1,HEADING_START=2,HEADING_DURING=3"}; heading:float; status:enum{RUNNING="0,DONE=1,CANCELED=2,ERROR=3"} | Move to changed. The drone moves or moved to a given location. (V: XML) | GEN 0x59b4c | XML: 090c from firmware 4.3.0 |
| MotionState | 1.4.13 | send | state:enum{steady="0,moving=1"} | Motion state. If MotionDetection is disabled, motion is steady. This information is only valid when the drone is not flying. (V: XML) | GEN 0x5b088 | XML: 090c from firmware 4.3.0 |
| PilotedPOI | 1.4.14 | send | latitude:double; longitude:double; altitude:double; status:enum{UNAVAILABLE="0,AVAILABLE=1,PENDING=2,RUNNING=3"} | Piloted POI state. (V: XML) | GEN 0x593b8 | XML: deprecated; XML: 090c from firmware 4.3.0 |
Ardrone3.Animations (class 5)
Section titled “Ardrone3.Animations (class 5)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| Flip | 1.5.0 | receive | direction:enum{front="0,back=1,right=2,left=3"} | Make a flip. (V: XML) | REG 0x6108c cb 0x58294; msg 152 ANIMATION_START (A) | gate: bebop2-flip-acceptance.md (Agent-cited): gate A allows only Hovering, Flying, HoveringGps, GoToFix, Animation (-11 otherwise); then horizontal speed < thresholdMaxHorizontalSpeedForFlip (10.0) and battery > tresholdVbatMinForFlipPercent (4.0); FSM drops the event in GoToFix and Animation; refusals are silent to the controller; Directions are FRONT 0, BACK 1, RIGHT 2, LEFT 3 in the firmware (V). |
Ardrone3.PilotingSettingsState (class 6)
Section titled “Ardrone3.PilotingSettingsState (class 6)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| MaxAltitudeChanged | 1.6.0 | send | current:float; min:float; max:float | Max altitude. The drone will not fly higher than this altitude (above take off point). (V: XML) | GEN 0x5b1b4 | |
| MaxTiltChanged | 1.6.1 | send | current:float; min:float; max:float | Max pitch/roll. The drone will not fly higher than this altitude (above take off point). (V: XML) | GEN 0x5b82c | |
| MaxDistanceChanged | 1.6.3 | send | current:float; min:float; max:float | Max distance. (V: XML) | GEN 0x5b3f4 | |
| NoFlyOverMaxDistanceChanged | 1.6.4 | send | shouldNotFlyOver:u8 | Geofencing. If set, the drone won’t fly over the MaxDistance. (V: XML) | GEN 0x5b58c | |
| AutonomousFlightMaxHorizontalSpeed | 1.6.5 | send | value:float | Autonomous flight max horizontal speed. (V: XML) | GEN 0x5bee8 | XML: 090c from firmware 3.3.0 |
| AutonomousFlightMaxVerticalSpeed | 1.6.6 | send | value:float | Autonomous flight max vertical speed. (V: XML) | GEN 0x5bff8 | XML: 090c from firmware 3.3.0 |
| AutonomousFlightMaxHorizontalAcceleration | 1.6.7 | send | value:float | Autonomous flight max horizontal acceleration. (V: XML) | GEN 0x5c108 | XML: 090c from firmware 3.3.0 |
| AutonomousFlightMaxVerticalAcceleration | 1.6.8 | send | value:float | Autonomous flight max vertical acceleration. (V: XML) | GEN 0x5c218 | XML: 090c from firmware 3.3.0 |
| AutonomousFlightMaxRotationSpeed | 1.6.9 | send | value:float | Autonomous flight max rotation speed. (V: XML) | GEN 0x5bdd8 | XML: 090c from firmware 3.3.0 |
| BankedTurnChanged | 1.6.10 | send | state:u8 | Banked Turn mode. If banked turn mode is enabled, the drone will use yaw values from the piloting command to infer with roll and pitch on the drone when its horizontal speed is not null. (V: XML) | GEN 0x5b944 | XML: 090c from firmware 3.2.0 |
| MotionDetection | 1.6.16 | send | enabled:u8 | State of the motion detection. (V: XML) | GEN 0x5b6f0 | XML: 090c from firmware 4.3.0 |
Ardrone3.MediaRecord (class 7)
Section titled “Ardrone3.MediaRecord (class 7)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| PictureV2 | 1.7.2 | receive | (none) | Take a picture. The type of picture taken is related to the picture setting. You can set the picture format by sending the command SetPictureFormat. You can also get the current picture format with PictureFormat. (V: XML) | REG 0x60ba4 cb 0x57f58; msg 52 PHOTO_RECORD_V2 (A) | |
| VideoV2 | 1.7.3 | receive | record:enum{stop="0,start=1"} | Record a video (or start timelapse). You can check if the video recording is available with VideoState. This command can start a video (obvious huh?), but also a timelapse if the timelapse mode is set. (V: XML) | REG 0x60bb8 cb 0x57e48; msg 48 VIDEO_RECORD_START_V2, 49 VIDEO_RECORD_STOP_V2 (A) |
Ardrone3.MediaRecordState (class 8)
Section titled “Ardrone3.MediaRecordState (class 8)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| PictureStateChangedV2 | 1.8.2 | send | state:enum{ready="0,busy=1,notAvailable=2"}; error:enum{ok="0,unknown=1,camera_ko=2,memoryFull=3,lowBattery=4"} | Picture state. (V: XML) | GEN 0x59db4 | |
| VideoStateChangedV2 | 1.8.3 | send | state:enum{stopped="0,started=1,notAvailable=2"}; error:enum{ok="0,unknown=1,camera_ko=2,memoryFull=3,lowBattery=4"} | Video record state. (V: XML) | GEN 0x59fd4 |
Ardrone3.NetworkSettings (class 9)
Section titled “Ardrone3.NetworkSettings (class 9)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| WifiSelection | 1.9.0 | receive | type:enum{auto="0,manual=1"}; band:enum{2_4ghz="0,5ghz=1,all=2"}; channel:u8 | Select Wifi. Select or auto-select channel of choosen band. (V: XML) | REG 0x60e94 cb 0x573d4; msg 115 WIFI_SELECT (A) | |
| WifiSecurity | 1.9.1 | receive | type:enum{open="0,wpa2=1"}; key:string; keyType:enum{plain="0"} | Set wifi security type. The security will be changed on the next restart (V: XML) | REG 0x60ed0 cb 0x5672c; msg 120 WIFI_SECURITY (A) |
Ardrone3.NetworkSettingsState (class 10)
Section titled “Ardrone3.NetworkSettingsState (class 10)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| WifiSelectionChanged | 1.10.0 | send | type:enum{auto_all="0,auto_2_4ghz=1,auto_5ghz=2,manual=3"}; band:enum{2_4ghz="0,5ghz=1,all=2"}; channel:u8 | Wifi selection. (V: XML) | GEN 0x5e44c | |
| WifiSecurityChanged | 1.10.1 | send | type:enum{open="0,wpa2=1"} | Wifi security type. (V: XML) | GEN 0x5e8e0 | XML: deprecated; XML gives no support value |
| WifiSecurity | 1.10.2 | send | type:enum{open="0,wpa2=1"}; key:string; keyType:enum{plain="0"} | Wifi security type. (V: XML) | GEN 0x5e8b0 |
Ardrone3.SpeedSettings (class 11)
Section titled “Ardrone3.SpeedSettings (class 11)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| MaxVerticalSpeed | 1.11.0 | receive | current:float | Set max vertical speed. (V: XML) | REG 0x60cc8 cb 0x56070; msg 74 SET_MAX_VERTICAL_SPEED (A) | |
| MaxRotationSpeed | 1.11.1 | receive | current:float | Set max rotation speed. (V: XML) | REG 0x60cdc cb 0x55fe8; msg 75 SET_MAX_ROTATION_SPEED (A) | |
| HullProtection | 1.11.2 | receive | present:u8 | Set the presence of hull protection. (V: XML) | REG 0x60d04 cb 0x55ed8; msg 78 SET_HULL_PROTECTION (A) | |
| Outdoor | 1.11.3 | receive | outdoor:u8 | Set outdoor mode. (V: XML) | REG 0x60d18 cb 0x5c528; no msg id found (O) | XML: deprecated; XML gives no support value; Callback 0x5c528 does not use the 0x6a374 poster; effect not traced (O). |
| MaxPitchRollRotationSpeed | 1.11.4 | receive | current:float | Set max pitch/roll rotation speed. (V: XML) | REG 0x60cf0 cb 0x55f60; msg 77 SET_MAX_ANGULAR_RATE (A) |
Ardrone3.SpeedSettingsState (class 12)
Section titled “Ardrone3.SpeedSettingsState (class 12)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| MaxVerticalSpeedChanged | 1.12.0 | send | current:float; min:float; max:float | Max vertical speed. (V: XML) | GEN 0x5ba88 | |
| MaxRotationSpeedChanged | 1.12.1 | send | current:float; min:float; max:float | Max rotation speed. (V: XML) | GEN 0x5bba4 | |
| HullProtectionChanged | 1.12.2 | send | present:u8 | Presence of hull protection. (V: XML) | GEN 0x5c32c | |
| OutdoorChanged | 1.12.3 | send | outdoor:u8 | Outdoor mode. (V: XML) | GEN 0x5c440 | XML: deprecated; XML gives no support value |
| MaxPitchRollRotationSpeedChanged | 1.12.4 | send | current:float; min:float; max:float | Max pitch/roll rotation speed. (V: XML) | GEN 0x5bcc0 |
Ardrone3.Network (class 13)
Section titled “Ardrone3.Network (class 13)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| WifiScan | 1.13.0 | receive | band:enum{2_4ghz="0,5ghz=1,all=2"} | Scan wifi network to get a list of all networks found by the drone (V: XML) | REG 0x60ea8 cb 0x572ec; msg 113 WIFI_SCAN (A) | |
| WifiAuthChannel | 1.13.1 | receive | (none) | Ask for available wifi channels. The list of available Wifi channels is related to the country of the drone. You can get this country from the event CountryChanged. (V: XML) | REG 0x60ebc cb 0x5588c; msg 116 WIFI_AUTH_CHANNEL_INQUIRY (A) |
Ardrone3.NetworkState (class 14)
Section titled “Ardrone3.NetworkState (class 14)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| WifiScanListChanged | 1.14.0 | send | ssid:string; rssi:i16; band:enum{2_4ghz="0,5ghz=1"}; channel:u8 | Wifi scan results. Please note that the list is not complete until you receive the event WifiScanEnded. (V: XML) | GEN 0x5e1bc | |
| AllWifiScanChanged | 1.14.1 | send | (none) | Wifi scan ended. When receiving this event, the list of WifiScanResults is complete. (V: XML) | GEN 0x5e314 | |
| WifiAuthChannelListChanged | 1.14.2 | send | band:enum{2_4ghz="0,5ghz=1"}; channel:u8; in_or_out:u8 | Available wifi channels. Please note that the list is not complete until you receive the event AvailableWifiChannelsCompleted. (V: XML) | GEN 0x5e598 | |
| AllWifiAuthChannelChanged | 1.14.3 | send | (none) | Available wifi channels completed. When receiving this event, the list of AvailableWifiChannels is complete. (V: XML) | GEN 0x5e720 |
Ardrone3.SettingsState (class 16)
Section titled “Ardrone3.SettingsState (class 16)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| ProductGPSVersionChanged | 1.16.1 | send | software:string; hardware:string | GPS version. (V: XML) | GEN 0x5d7a0 | |
| MotorErrorStateChanged | 1.16.2 | send | motorIds:u8; motorError:enum{noError="0,errorEEPRom=1,errorMotorStalled=2,errorPropellerSecurity=3,errorCommLost=4,errorRCEmergencyStop=5,errorRealTime=6,errorMotorSetting=7,errorTemperature=8,errorBatteryVoltage=9,errorLipoCells=10,errorMOSFET=11,errorBootloader=12,errorAssert=13"} | Motor error. This event is sent back to noError as soon as the motor error disappear. To get the last motor error, see LastMotorError (V: XML) | GEN 0x5ed3c | |
| MotorSoftwareVersionChanged | 1.16.3 | send | version:string | Motor version. (V: XML) | GEN 0x5eef8 | XML: deprecated; XML gives no support value |
| MotorFlightsStatusChanged | 1.16.4 | send | nbFlights:u16; lastFlightDuration:u16; totalFlightDuration:u32 | Motor flight status. (V: XML) | GEN 0x5f068 | |
| MotorErrorLastErrorChanged | 1.16.5 | send | motorError:enum{noError="0,errorEEPRom=1,errorMotorStalled=2,errorPropellerSecurity=3,errorCommLost=4,errorRCEmergencyStop=5,errorRealTime=6,errorMotorSetting=7,errorBatteryVoltage=8,errorLipoCells=9,errorMOSFET=10,errorTemperature=11,errorBootloader=12,errorAssert=13"} | Last motor error. This is a reminder of the last error. To know if a motor error is currently happening, see MotorError. (V: XML) | GEN 0x5f098 | |
| P7ID | 1.16.6 | send | serialID:string | P7ID. (V: XML) | GEN 0x5cec0 | XML: deprecated; XML gives no support value |
| CPUID | 1.16.7 | send | id:string | (no text in the XML) (V: XML) | GEN 0x5cd64 | XML gives no support value |
Ardrone3.PictureSettings (class 19)
Section titled “Ardrone3.PictureSettings (class 19)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| PictureFormatSelection | 1.19.0 | receive | type:enum{raw="0,jpeg=1,snapshot=2,jpeg_fisheye=3"} | Set picture format. Please note that the time required to take the picture is highly related to this format. (V: XML) | REG 0x60d90 cb 0x57814; msg 86 SET_PICTURE_FORMAT (A) | |
| AutoWhiteBalanceSelection | 1.19.1 | receive | type:enum{auto="0,tungsten=1,daylight=2,cloudy=3,cool_white=4"} | Set White Balance mode. (V: XML) | REG 0x60da4 cb 0x57788; msg 87 SET_AUTOWHITEBALANCE (A) | |
| ExpositionSelection | 1.19.2 | receive | value:float | Set image exposure. (V: XML) | REG 0x60db8 cb 0x55ba8; msg 88 SET_EXPOSURE (A) | |
| SaturationSelection | 1.19.3 | receive | value:float | Set image saturation. (V: XML) | REG 0x60dcc cb 0x55b20; msg 89 SET_SATURATION (A) | |
| TimelapseSelection | 1.19.4 | receive | enabled:u8; interval:float | Set timelapse mode. If timelapse mode is set, instead of taking a video, the drone will take picture regularly. Watch out, this command only configure the timelapse mode. Once it is configured, you can start/stop the timelapse with the RecordVideo command. (V: XML) | REG 0x60de0 cb 0x576f8; msg 90 SET_TIMELAPSE (A) | |
| VideoAutorecordSelection | 1.19.5 | receive | enabled:u8; mass_storage_id:u8 | Set video autorecord mode. If autorecord is set, video record will be automatically started when the drone takes off and stopped slightly after landing. (V: XML) | REG 0x60df4 cb 0x55a98; msg 91 SET_VIDEO_AUTORECORD (A) | |
| VideoStabilizationMode | 1.19.6 | receive | mode:enum{roll_pitch="0,pitch=1,roll=2,none=3"} | Set video stabilization mode. (V: XML) | REG 0x60e08 cb 0x5766c; msg 92 SET_VIDEO_STABILIZATION_MODE (A) | XML: 090c from firmware 3.4.0 |
| VideoRecordingMode | 1.19.7 | receive | mode:enum{quality="0,time=1"} | Set video recording mode. (V: XML) | REG 0x60bf4 cb 0x57c30; msg 93 SET_VIDEO_RECORDING_MODE (A) | XML: 090c from firmware 3.4.0 |
| VideoFramerate | 1.19.8 | receive | framerate:enum{24_FPS="0,25_FPS=1,30_FPS=2"} | Set video framerate. (V: XML) | REG 0x60c08 cb 0x57b2c; msg 94 SET_VIDEO_FRAMERATE (A) | XML: 090c from firmware 3.4.0 |
| VideoResolutions | 1.19.9 | receive | type:enum{rec1080_stream480="0,rec720_stream720=1"} | Set video resolutions. Set video streaming and recording resolutions. (V: XML) | REG 0x60c1c cb 0x57a2c; msg 95 SET_VIDEO_RESOLUTION_MODE (A) | XML: 090c from firmware 3.4.0 |
Ardrone3.PictureSettingsState (class 20)
Section titled “Ardrone3.PictureSettingsState (class 20)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| PictureFormatChanged | 1.20.0 | send | type:enum{raw="0,jpeg=1,snapshot=2,jpeg_fisheye=3"} | Picture format. (V: XML) | GEN 0x5c5c0 | |
| AutoWhiteBalanceChanged | 1.20.1 | send | type:enum{auto="0,tungsten=1,daylight=2,cloudy=3,cool_white=4"} | White balance mode. (V: XML) | GEN 0x5c6d4 | |
| ExpositionChanged | 1.20.2 | send | value:float; min:float; max:float | Image exposure. (V: XML) | GEN 0x5c7ec | |
| SaturationChanged | 1.20.3 | send | value:float; min:float; max:float | Image saturation. (V: XML) | GEN 0x5c904 | |
| TimelapseChanged | 1.20.4 | send | enabled:u8; interval:float; minInterval:float; maxInterval:float | Timelapse mode. (V: XML) | GEN 0x5ca20 | |
| VideoAutorecordChanged | 1.20.5 | send | enabled:u8; mass_storage_id:u8 | Video Autorecord mode. (V: XML) | GEN 0x5cb38 | |
| VideoStabilizationModeChanged | 1.20.6 | send | mode:enum{roll_pitch="0,pitch=1,roll=2,none=3"} | Video stabilization mode. (V: XML) | GEN 0x5cc4c | XML: 090c from firmware 3.4.0 |
| VideoRecordingModeChanged | 1.20.7 | send | mode:enum{quality="0,time=1"} | Video recording mode. (V: XML) | GEN 0x5a8a8 | XML: 090c from firmware 3.4.0 |
| VideoFramerateChanged | 1.20.8 | send | framerate:enum{24_FPS="0,25_FPS=1,30_FPS=2"} | Video framerate. (V: XML) | GEN 0x5ab7c | XML: 090c from firmware 3.4.0 |
| VideoResolutionsChanged | 1.20.9 | send | type:enum{rec1080_stream480="0,rec720_stream720=1"} | Video resolutions. This event informs about the recording AND streaming resolutions. (V: XML) | GEN 0x5ace8 | XML: 090c from firmware 3.4.0 |
Ardrone3.MediaStreaming (class 21)
Section titled “Ardrone3.MediaStreaming (class 21)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| VideoEnable | 1.21.0 | receive | enable:u8 | Enable/disable video streaming. (V: XML) | REG 0x60b90 cb 0x56440; msg 43 VIDEO_STREAMING_ENABLE (A) | |
| VideoStreamMode | 1.21.1 | receive | mode:enum{low_latency="0,high_reliability=1,high_reliability_low_framerate=2"} | Set the stream mode. (V: XML) | REG 0x60c30 cb 0x57928; msg 96 SET_VIDEO_STREAMING_MODE (A) |
Ardrone3.MediaStreamingState (class 22)
Section titled “Ardrone3.MediaStreamingState (class 22)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| VideoEnableChanged | 1.22.0 | send | enabled:enum{enabled="0,disabled=1,error=2"} | Video stream state. (V: XML) | GEN 0x5eab8 | |
| VideoStreamModeChanged | 1.22.1 | send | mode:enum{low_latency="0,high_reliability=1,high_reliability_low_framerate=2"} | (no text in the XML) (V: XML) | GEN 0x5aa10 | XML gives no support value |
Ardrone3.GPSSettings (class 23)
Section titled “Ardrone3.GPSSettings (class 23)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| SetHome | 1.23.0 | receive | latitude:double; longitude:double; altitude:double | Set home position. (V: XML) | REG 0x60e1c cb 0x575dc; msg 107 SET_GPS_HOME (A) | XML: deprecated; XML gives no support value |
| ResetHome | 1.23.1 | receive | (none) | Reset home position. (V: XML) | REG 0x60e30 cb 0x57564; msg 109 RESET_GPS_HOME (A) | XML: deprecated |
| SendControllerGPS | 1.23.2 | receive | latitude:double; longitude:double; altitude:double; horizontalAccuracy:double; verticalAccuracy:double | Set controller gps location. The user location might be used in case of return home, according to the home type and the accuracy of the given position. You can get the current home type with the event HomeType. (V: XML) | REG 0x60e44 cb 0x5747c; msg 107 SET_GPS_HOME (A) | |
| HomeType | 1.23.3 | receive | type:enum{TAKEOFF="0,PILOT=1,FOLLOWEE=2"} | Set the preferred home type. Please note that this is only a preference. The actual type chosen is given by the event HomeType. You can get the currently available types with the event HomeTypeAvailability. (V: XML) | REG 0x60e58 cb 0x55a10; msg 108 SET_GPS_HOME_TYPE (A) | |
| ReturnHomeDelay | 1.23.4 | receive | delay:u16 | Set the return home delay. Set the delay after which the drone will automatically try to return home after a disconnection. (V: XML) | REG 0x60e6c cb 0x55988; msg 110 SET_RETURN_HOME_DELAY (A) | |
| ReturnHomeMinAltitude | 1.23.5 | receive | value:float | Set the return home min altitude. Set the return home minimum altitude. If the drone is below this altitude when starting its return home, it will first reach the minimum altitude. (V: XML) | REG 0x60e80 cb 0x55900; msg 62 SET_RTH_MIN_ALTITUDE (A) | XML support attribute is empty |
Ardrone3.GPSSettingsState (class 24)
Section titled “Ardrone3.GPSSettingsState (class 24)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| GPSFixStateChanged | 1.24.2 | send | fixed:u8 | Gps fix info. (V: XML) | GEN 0x5d54c | |
| GPSUpdateStateChanged | 1.24.3 | send | state:enum{updated="0,inProgress=1,failed=2"} | Gps update state. (V: XML) | GEN 0x5d660 | XML: deprecated |
| HomeTypeChanged | 1.24.4 | send | type:enum{TAKEOFF="0,PILOT=1,FOLLOWEE=2"} | Preferred home type. User preference for the home type. See HomeType to get the drone actual home type. (V: XML) | GEN 0x5dbbc | |
| ReturnHomeDelayChanged | 1.24.5 | send | delay:u16 | Return home delay. Return home trigger delay. This delay represents the time after which the return home is automatically triggered after a disconnection. (V: XML) | GEN 0x5da4c | |
| ReturnHomeMinAltitudeChanged | 1.24.7 | send | value:float; min:float; max:float | Return home min altitude. Minumum altitude for return home changed. (V: XML) | GEN 0x5b2d0 | XML gives no support value |
Ardrone3.CameraState (class 25)
Section titled “Ardrone3.CameraState (class 25)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| Orientation | 1.25.0 | send | tilt:i8; pan:i8 | Camera orientation. (V: XML) | GEN 0x5a64c | XML: deprecated |
| DefaultCameraOrientation | 1.25.1 | send | tilt:i8; pan:i8 | Orientation of the camera center. Orientation of the center of the camera. This is the value to send when you want to center the camera. (V: XML) | GEN 0x5a310 | XML: deprecated |
| OrientationV2 | 1.25.2 | send | tilt:float; pan:float | Camera orientation with float arguments. (V: XML) | GEN 0x5a75c | |
| DefaultCameraOrientationV2 | 1.25.3 | send | tilt:float; pan:float | Orientation of the camera center. Orientation of the center of the camera. This is the value to send when you want to center the camera. (V: XML) | GEN 0x5a420 | |
| VelocityRange | 1.25.4 | send | max_tilt:float; max_pan:float | Camera velocity range. Camera Orientation velocity limits. (V: XML) | GEN 0x5a530 |
Ardrone3.Antiflickering (class 29)
Section titled “Ardrone3.Antiflickering (class 29)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| ElectricFrequency | 1.29.0 | receive | frequency:enum{fiftyHertz="0,sixtyHertz=1"} | Set the electric frequency of the surrounding lights. This is used to avoid the video flickering in auto mode. You can get the current antiflickering mode with the event AntiflickeringModeChanged. (V: XML) | REG 0x60bcc cb 0x57dbc; msg 46 SET_ELECTRIC_FREQUENCY (A) | |
| SetMode | 1.29.1 | receive | mode:enum{auto="0,FixedFiftyHertz=1,FixedSixtyHertz=2"} | Set the antiflickering mode. If auto, the drone will detect when flickers appears on the video and trigger the antiflickering. In this case, this electric frequency it will use will be the one specified in the event ElectricFrequency. (V: XML) | REG 0x60be0 cb 0x57d30; msg 47 SET_ANTIFLICKERING_MODE (A) |
Ardrone3.AntiflickeringState (class 30)
Section titled “Ardrone3.AntiflickeringState (class 30)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| ElectricFrequencyChanged | 1.30.0 | send | frequency:enum{fiftyHertz="0,sixtyHertz=1"} | Electric frequency. This piece of information is used for the antiflickering when the AntiflickeringMode is set to auto. (V: XML) | GEN 0x5ae18 | |
| ModeChanged | 1.30.1 | send | mode:enum{auto="0,FixedFiftyHertz=1,FixedSixtyHertz=2"} | Antiflickering mode. (V: XML) | GEN 0x5af2c |
Ardrone3.GPSState (class 31)
Section titled “Ardrone3.GPSState (class 31)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| NumberOfSatelliteChanged | 1.31.0 | send | numberOfSatellite:u8 | Number of GPS satellites. (V: XML) | GEN 0x5d8f8 | |
| HomeTypeAvailabilityChanged | 1.31.1 | send | type:enum{TAKEOFF="0,PILOT=1,FIRST_FIX=2,FOLLOWEE=3"}; available:u8 | Home type availability. (V: XML) | GEN 0x5dd70 | |
| HomeTypeChosenChanged | 1.31.2 | send | type:enum{TAKEOFF="0,PILOT=1,FIRST_FIX=2,FOLLOWEE=3"} | Home type. This choice is made by the drone, according to the PreferredHomeType and the HomeTypeAvailability. The drone will choose the type matching with the user preference only if this type is available. (V: XML) | GEN 0x5dfa8 |
Ardrone3.PROState (class 32)
Section titled “Ardrone3.PROState (class 32)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| Features | 1.32.0 | send | features:u64 | Pro features. (V: XML) | GEN 0x5cfe0 | XML: deprecated; XML gives no support value |
Ardrone3.AccessoryState (class 33)
Section titled “Ardrone3.AccessoryState (class 33)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| ConnectedAccessories | 1.33.0 | send | id:u8; accessory_type:enum{sequoia="0,flir=1"}; uid:string; swVersion:string; list_flags:u8 | List of connected accessories. List of all connected accessories. This event presents the list of all connected accessories. To actually use the component, use the component dedicated feature. (V: XML) | GEN 0x6447c | XML support “090e:1.5.0” lists no 090c |
Ardrone3.PilotingEvent (class 34)
Section titled “Ardrone3.PilotingEvent (class 34)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| MoveByEnd | 1.34.0 | send | dX:float; dY:float; dZ:float; dPsi:float; error:enum{ok="0,unknown=1,busy=2,notAvailable=3,interrupted=4"} | Relative move ended. Informs about the move that the drone managed to do and why it stopped. (V: XML) | GEN 0x59c98 | XML: 090c from firmware 3.3.0 |
Ardrone3.Sound (class 35)
Section titled “Ardrone3.Sound (class 35)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| StartAlertSound | 1.35.0 | receive | (none) | Start alert sound. Start the alert sound. The alert sound can only be started when the drone is not flying. (V: XML) | REG 0x61060 cb 0x56bdc; msg 154 START_ALERT_SOUND (A) | XML support “none” lists no 090c |
| StopAlertSound | 1.35.1 | receive | (none) | Stop alert sound. Stop the alert sound. (V: XML) | REG 0x61078 cb 0x56b64; msg 155 STOP_ALERT_SOUND (A) | XML support “none” lists no 090c |
Ardrone3.SoundState (class 36)
Section titled “Ardrone3.SoundState (class 36)”| Command | Id | Dir | Arguments | What it does | Status in dragon-prog | Notes |
|---|---|---|---|---|---|---|
| AlertSound | 1.36.0 | send | state:enum{stopped="0,playing=1"} | Alert sound state. (V: XML) | GEN 0x59120 | XML support “none” lists no 090c |
Comments
Spotted a mistake, or tried this on your own Bebop? Leave a note. Comments are kept on this site's own server.